SKETCHUP 2015 FOR DUMMIES SOFTWARE

SheвЂ™ll cover basic design software that can help you understand the basics of 3D design, with videos included as examples. In the video I also then group, rotate, and reposition what I drew.You may have seen Lydia ClineвЂ™s creations around Pinshape, but did you know sheвЂ™s written books on 3D design? SheвЂ™s here today to give beginners a place to start their 3D design journey. You should now have a 4ењ†ft table, with 36 inch legs, 4x4 inches. Pushpull will extrude the same distance as last time Point to the other 3 squares in turn and double click.

Grab the pushpull tool and pull one of these little squares out by 36 inches (click, move as to pull out, type 3 6 RETURN. Now with the rectangle tool, point in each corner where guide lines cross, click-move(towards the table centre)-click, type 4, 4 RETURN. Repeat the process for the remaining sides. A guide line should appear, in dots, set in 2 inches from the table edge. Now grab your tape tool, point to the long edge of the table, click, move towards the middle of the table, type 2 RETURN. Remember that the direction youвЂ™re now pushing is the 24 inch direction, and suppose you want a table top 2 inches thick - so type 22 RETURN (24 inches already, squished down by 22 inches, is 2 inches thick cuboid) Click and move the mouse to squash the cuboid down again. Now point at the cuboid face that is 4ftењ†ft - it goes blue. if ever it seems that youвЂ™re interacting with the wrong part of the model, press ESC followed by Ctrl-T ) Press Ctrl-T (this ensures nothing is selected - so much to tell a newbie, even things like understanding how selection works is complex - some tools operate on already-selected things, some tools select things when you point to them. LetвЂ™s turn your cuboid into an ordinary table. You should always try to write the dimensions of everything into the dims box, then you donвЂ™t have any вЂњapproximately 24 inchesвЂќ problems You should always try and draw things relative to something else because youвЂ™re using a 2D screen to play with a 3D world. Use the eraser tool to erase the line you just drew Move the mouse to the diagonally opposite corner, see the dot appear indicating SU attention has snapped to the opposite corner, and click-release again. Type 72 RETURN on the keyboard and now you have a 2ft x 4ft x 6ft cuboidДraw a diagonal line from corner to corner on one face: choose LINE tool or push L, point the mouse at one corner, until a dot appears вЂњstuckвЂќ to the corner - this indicates sketchup has snapped its attention to that corner. Now find the PushPull tool (cuboid with an up arrow, remember to hover your mouse over the tools to see the names until you are familiar with them - or push the P key), point your mouse at the rectangle, see that it goes blue indicating it is selected to be push/pulledвЂ¦ Click the mouse, move it some way and click again. When you press return, the rectangle snaps to be 2 ft by 4 ft YouвЂ™ll see 24,48 appear in the dims box in the bottom left as you type. It doesnвЂ™t matter whether you click again to stop drawing or not, but just type on the keyboard the following keys: 2 4, 4 8 RETURN now move the mouse and see the rectangle appear. Now, letвЂ™s just start with a rectangle - choose the rectangle tool, click the mouse in the drawing area and release the mouse button. Now, point to ANY icon that is a tool (like the arrow, paint bucket, hand etc) and right clic. In there go to DRAWING and ensure hat вЂњclick-move-clickвЂќ is enabled rather than autodetect or click-drag-release I definitely think youвЂ™d be better off not starting by drawing the thing you want to draw draw something simpler instead, to get used to the user interface we can watch what youвЂ™re doing and instantly se whatвЂ™s going wrong and not only correct the problem but also educate away whatever misconception is causing it Maybe most of all, use a screen recording program like bbflashback and record yourself using it, then post your video here. Start really basic, watch the tutorial for drawing a house (draw a rectangle, pull it up, draw a line for the roof apex, move it up so it bends the roof planes etc)

If your dims have a ~ in front of them then either the scale of your model is so small that SU cannot represent it properly (like millionths of an inch or something - and you drew a line 24 millionths of an inch long), or you did not type the length in after you drew it but instead used the mouse and dragged to вЂњsomewhere near 24 inchesвЂќ You cannot make any inference from how big something вЂњlooksвЂќ in sketchup - IвЂ™ve drawn an entire house and itвЂ™s about 6 inches big when I zoom out Next, like was earlier mentioned, just draw things and then type on the keyboard to get exact dimensioned entities, so draw a rectangle of any size, and then type the following keys: to get it 24 inches by 48 inches First off, if you want to work in inches, ensure your world units are set to inches.

Sketchup 2015 for dummies